-
Main ApplicationLarge bars and small nightclub bass frequency reinforcement / portable live music PA
-
Complementary SpeakersCan be reinforced with TFR 1001/1201/1202/1502S/1502L full range cabinets
-
DimensionsW: 53cm. H: 58.5cm. D: 60cm
-
Power700w RMS. 1400w Peak
-
Drivers1 x 15” bass driver
-
MountingFloor based
-
Quick SpecsRF15 features a single loaded 15” reflex bass driver and has a frequency response of 45Hz to 120Hz
-
ModelRF15
-
TypeVented Reflex Bass Cabinet
-
Frequency ResponseFrom 45Hz – 120Hz
-
Rated Power700w RMS – 1400w Peak
-
Sensitivity96db
-
Maximum SPL120db
-
Dispersion–
-
Nominal8 Ohms
-
Bass15” Driver
-
Mid–
-
High Frequency–
-
Crossover–
-
EnclosureMulti Laminated Birch Ply
-
FinishTextured Black Paint
-
GrilleBlack Perforated Steel
-
Connector2 x Neutrik NL4
-
Fittings1 x Top Hat Fitting 2 x Recessed Bar Handles 4 Castors
-
DimensionsW: 53cm. H: 58.5cm. D: 60cm
-
Weight–
Each connector panel has two Neutrik Speakon connectors wired in parallel. The second connector allows use of a short link lead to power a secondary parallel loudspeaker. The connectors are wired as follows:
- 2 Core cable
- Pin 1 Positive
- Pin 1 Negative
When connecting Blacka Group sound reinforcement to an amplifier it is recommended that the return resistance of the cable used is less than one tenth of the normal impedance of the system or systems in parallel the chart below gives an indication of the maximum possible cable runs for conductor cross sectional areas.
-
Conductor CSAMaximum Cable Lengths
-
4 OHMS8 OHMS10 OHMS
-
1.0 mm11 m22 m44 m
-
1.5 mm17 m34 m68 m
-
2.0 mm22 m44 m88 m
-
2.5 mm29 m58 m116 m
-
4.0 mm44 m88 m176 m
-
6.0 mm66 m132 m264 m
The Blacka Group RF15 is designed to be used with professional power amplifiers capable of producing 700w – 1400w power output into 4 ohms.
Care should be taken to avoid amplifier clipping, it is important to understand that a low power amplifier driven into clipping is more likely to damage a loud speaker than a higher power amplifier used within its ratings. Primarily because music signals have a high peak to average crest factor. When an amplifier is severely overdriven its output waveform is clipped resulting in squared off peaks and thus reducing the crest factor. In extreme cases, the waveform can approach that of a square wave. An amplifier is normally capable of producing far more power under these conditions than its undistorted rated power output. The use of very high power amplifiers with outputs greater than those recommended is discouraged.
Care should be taken to avoid switch on surges, which can result in momentary power peaks in excess of specified ratings. When powering up a sound system it is important to switch on the amplifiers after the mixer and control electronics have stabilised. When powering down the system, reverse the sequence and switch off the amplifiers first.
The RF12 units can be used with a wide array of Blacka Group speakers. Typical configurations are listed below
Large Bars/Small Nightclubs: TFR 25T – TFR 801 – TFR 1001 – TFR 1201 – TFR 1202 – TFR 1502S – TFR 1502L
It is important that loudspeaker systems are used in a safe manner. Please take some time to review the following points concerning use of Blacka Group Loudspeakers.
Professional loudspeakers are capable of producing extremely high sound levels and should be used with care. Hearing loss is cumulative and can result from levels above 90 DB if people are exposed for a long period , never stand close to loudspeakers driven at high level.
STACKING
- Ensure that the floor or stage is level and solid.
- Be aware that these speakers produce very high levels of output, So be aware that they can move or creep.